Turning On and Off the Power
To turn the machine on and off, press the main power switch on the front right side of the machine.
When you are using the fax function on the machine, do not turn the power off under normal operation. If the power is turned off, data stored in the fax memory will be lost in about one hour after the machine is turned off. If you have to turn the power off or unplug the power cord for some reason, make sure 100% is shown as available memory on the screen for the fax function.
Do not press the main power switch repeatedly. When you turn the power on or off, wait at least 10 seconds after confirming that the main power indicator on the right side of the control panel has turned on or off.
Make sure the power cord is firmly plugged into the wall outlet.
Open the cover of the main power switch on the front right side of the machine, and push the switch.
The main power indicator on the right side of the control panel turns on.
When the power is turned on, the screen may show that the machine is performing an auto restart. Do not turn off the main power while the machine is processing. It takes about 5 minutes until the machine restarts.
If a file was deleted from memory, a Power Failure report is automatically printed as soon as the power is restored. This report can be used to identify lost files.
Do not turn off the power while the machine is in operation. To turn the power off, confirm that the operation is finished.
Do not hold down the main power switch while turning off the main power. Doing so forcibly turns off the machine's power and may damage the internal storage or memory and cause malfunctions.
Do not press the main power switch repeatedly. When you turn the power on or off, wait at least 10 seconds after confirming that the main power indicator on the right side of the control panel has turned on or off.
Open the cover of the main power switch on the front right side of the machine, and push the switch.
The main power indicator on the right side of the control panel turns off. The main power turns off automatically after the machine has shut down properly.
When the machine is not operated for a specified period of time, the machine enters the "Energy Saving mode" automatically. "Energy Saving mode" has two modes, "Fusing Unit Off mode" and "Sleep mode", and the machine enters the Fusing Unit Off mode first. In the factory default, the machine is configured to use both modes.
Fusing Unit Off Mode
In this mode, the main power indicator is lit. Because the heater of the fusing unit is turned off but the screen of the control panel is still displayed, the power consumption decreases, but you can start operation promptly. If you do not operate the machine for a specified period of time, the machine emits a clicking sound and enters Fusing Unit Off mode.
You can specify whether to enable the Fusing Unit Off mode and the time to wait before the machine enters Fusing Unit Off mode under [Fusing Unit Off Mode (Energy Saving) On/Off].
In this mode, you can scan documents, send faxes, receive faxes into memory, change the machine settings on the control panel, and perform other operations that do not require printing.
Sleep Mode
In this mode, the display of the control panel turns off and the main power indicator blinks slowly. Power consumption is minimized. When you do not operate the machine for a specified period of time or press [Energy Save] (
), the machine enters Sleep mode.
You can specify the amount of time that the machine waits before entering Sleep mode under [Sleep Mode Timer].
The machine recovers from Sleep mode when you perform one of the following:
Lift the ADF or exposure glass cover.
Place an original in the ADF.
Touch the display of the control panel.
The energy saving functions are disabled when an error occurs or while an operation is in progress.
The energy saving functions will not operate in the following cases:
When fixed warm-up is in progress
When operations are suspended during printing
When a warning message appears (The machine enters Fusing Unit Off mode unless the cover is open.)
When paper is jammed (The machine enters Fusing Unit Off mode except when the cover is open.)
When the Data In indicator is lit or flashing (The machine enters Fusing Unit Off mode except when the Data In indicator is lit or flashing due to receiving faxes or storing documents.)
The machine does not enter Sleep mode in the following cases:
During communication with external equipment
When the internal storage is active
When the service call message appears
When the ADF, machine's cover, or ADF cover are opened
When the "Add Toner" message appears
When toner is being replenished
When one of the following screens is displayed:
- System Settings
- Counter
- Inquiry
- Address Book
- Tray/Paper Settings
When data is being processed
If a file is waiting to be transmitted within the next minute using the "Send Later" facsimile function
When a recipient is being registered in the address list or group dial list
When the sample print, locked print, hold print, or stored print screen is displayed
When the screen of a document that was stored under the printer function appears
When the internal cooling fan is active
When accessing the machine using Web Image Monitor