Connecting to a Wired LAN

Connect the LAN cable to the machine, and then specify the IP address and other settings to connect to the Local Area Network (LAN) connection on the machine. There are two methods for configuration: settings in Wizard format (Settings) or manual settings in [System Settings].

Settings in Wizard format

Follow the instructions on the screen to specify [IP Address], [Subnet Mask], and [Gateway Address].

Setting in System Settings

Specify [IPv4 Address], [Subnet Mask], and [Gateway Address] manually. To display the IP address of the machine in the form of domain name (name resolution), also specify the DNS server.

Settings for the Connection in Wizard Format

Configure the settings from [Network Settings] of [Basic Settings When Installing].

  1. Press [Settings] on the Home screen.
    Operation panel screen illustration

  2. Press [Basic Settings When Installing] [Installation Settings].
    Operation panel screen illustration

  3. Press [Network Settings].

    Operation panel screen illustration

  4. Select [Wired LAN], and then press [Next].
    Operation panel screen illustration

  5. Insert the LAN cable in the corresponding port on the machine, and then press [Next].
    Operation panel screen illustration

  6. Select the method to obtain the IP address, and then press [Next].
    Operation panel screen illustration
    Auto-Obtain (DHCP): The machine obtains the IP address automatically from the DHCP server.
    Manual Setting: Select this when you are using a fixed IP address. Also specify IP Address, Subnet Mask, and Gateway Address.
    Proceed to the settings of the proxy setting and internet connection test as necessary.

  7. After completing the procedure, press [Set Up Complete], and then press [Home] ().

Section Top

Settings for the Connection in System Settings

Configure the settings from the [Network/Interface] in [System Settings].

  1. Press [Settings] on the Home screen.
    Operation panel screen illustration

  2. Press [System Settings].

    Operation panel screen illustration

  3. Press [Network/Interface] [Machine: LAN Type].

  4. Select [Wired LAN: Ethernet].
    Operation panel screen illustration

  5. Press [OK].

  6. Specify the IPv4 address of the main unit and DNS server address.

    Specifying the IP address automatically

    1. Press [IP Address (IPv4)].

    2. Press [IPv4 Address Configuration].

    3. Select [Auto-Obtain (DHCP)] from [IPv4 Address Configuration].
      Operation panel screen illustration
      Subnet Mask and Gateway Address are also obtained automatically.

    4. Press [OK].

    5. To specify the address of the DNS server, press [Operation panel screen illustration], and then press [DNS Configuration].

    6. Select [Auto-Obtain (DHCP)] from [DNS Configuration].
      Operation panel screen illustration

    7. Press [OK].

    Setting the IP address manually

    1. Press [IP Address (IPv4)].

    2. Press [IPv4 Address Configuration].

    3. Select [Specify] from [IPv4 Address Configuration].
      Operation panel screen illustration

    4. Press the input field for the IP Address, and then enter the IP Address.
      Operation panel screen illustration

    5. Press the input field for the Subnet Mask, and then enter the Subnet Mask.

    6. Confirm the entered information, and then press [OK].

    7. Press [IPv4 Gateway Address].

    8. Press the input field for the IPv4 Gateway Address, and then enter the IPv4 Gateway Address.

    9. Confirm the entered information, and then press [OK].

    10. To specify the address of the DNS server, press [], and then press [DNS Configuration].

    11. Select [Specify] from [DNS Configuration], press the input field for the IP Address for the DNS server, and then enter the IP Address.
      To specify the secondary DNS server, enter the IPv4 Address of the DNS servers in [DNS Server 2] and [DNS Server 3].

    12. Confirm the entered information, and then press [Connection Test].
      When [Connection to the server was successful.] is displayed, press [Exit].
      When [Failed to connect to the server.] is displayed, consult the administrator of the network to check whether the entered information is correct.

    13. Press [OK].

  7. After completing the procedure, press [Home] (Operation panel screen illustration).

Note

  • You can print the information of the network settings on the Configuration Page.
    List/Test Print

  • For the setting items of IPv6, see the following section:
    Network/Interface

Section Top

x

QR Code