Advanced Reduce/Enlarge Copying
This section describes the advanced functions for reducing or enlarging images.
For details about the basic reduce/enlarge copy functions, see Reducing or Enlarging Originals.
Size Magnification
Use this function to calculate a reproduction ratio based on the lengths of the original and copy.
Specify the lengths of the original and copy. The machine selects an enlargement or reduction ratio so that manual calculation is not required.
Press [Reduce / Enlarge].
Press [Size Magnification].
Enter the length of the original with the number keys, and then press [].
Enter the length of the copy with the number keys, and then press [].
Press [OK] twice.
You can enter sizes between 1 to 999 mm (0.1 to 99.9 inches) in increments of 1 mm (0.1 inches).
The reproduction ratio is between 25 and 400%.
If the calculated reproduction ratio falls below the minimum reproduction ratio, the calculated reproduction ratio will be adjusted to the minimum ratio. If the reproduction ratio is over the maximum reproduction ratio, it will be adjusted to the maximum ratio. If this happens, with some ratios, parts of the image might not be copied or margins will appear on copies.
Directional Magnification (%)
Specify the horizontal and vertical reproduction ratios, individually.
Copies can be reduced or enlarged at different reproduction ratios horizontally and vertically.
: Horizontal
: Vertical
To specify a reproduction ratio, enter the ratio using the number keys or specify the ratio with [] or [].
This section describes how to enter the ratio using the number keys.
Press [Reduce / Enlarge].
Press [Direct. Mag. %].
Press [Horizontal].
Enter the desired ratio with the number keys, and then press [].
When specifying the ratio with [] or [], press [Direct. Mag. %], and then press [[][] keys]. Pressing [] or [] after selecting [Horizontal] or [Vertical] changes the ratio in increments of 1%. Pressing and holding down [] or [] changes it in increments of 10%.
Press [Vertical].
Enter the desired ratio with the number keys, and then press [].
Press [OK] twice.
The reproduction ratio is between 25 and 400%.
You can select the ratio with priority when [Reduce / Enlarge] is pressed in Settings. For details, see the following section:
Directional Size Magnification (mm) (mainly Europe and Asia)
Specify the horizontal and vertical lengths of the original and copy image.
Copies can be reduced or enlarged at different reproduction ratios horizontally and vertically.
: Horizontal length
: Vertical length
Specify length and width of the originals and the copies.
Press [Reduce / Enlarge].
Press [Dir. Size Mag. mm].
Enter the horizontal size of the original with the number keys, and then press [].
Enter the horizontal size of the copy with the number keys, and then press [].
Enter the vertical size of the original with the number keys, and then press [].
Enter the vertical size of the copy with the number keys, and then press [].
Press [OK] twice.
The reproduction ratio is between 25 and 400%.
You can enter the horizontal length of an original and copies between 1 and 9999 mm in increments of 1 mm. You can enter the vertical length of an original and copies between 1 and 999 mm in increments of 1 mm.
If the calculated reproduction ratio falls below the minimum reproduction ratio, the calculated reproduction ratio will be adjusted to the minimum ratio. If the reproduction ratio is over the maximum reproduction ratio, it will be adjusted to the maximum ratio. If this happens, with some ratios, parts of the image might not be copied or margins will appear on copies.
Directional Size Magnification (inch) (mainly North America)
Specify the horizontal and vertical lengths of the original and copy image.
Copies can be reduced or enlarged at different reproduction ratios horizontally and vertically.
: Horizontal length
: Vertical length
Specify length and width of the originals and the copies.
Press [Reduce / Enlarge].
Press [Dir. Size Mag. inch].
Enter the horizontal size of the original with the number keys, and then press [].
Enter the horizontal size of the copy with the number keys, and then press [].
Enter the vertical size of the original with the number keys, and then press [].
Enter the vertical size of the copy with the number keys, and then press [].
Press [OK] twice.
The reproduction ratio is between 25 and 400%.
You can enter sizes between 0.1 and 99.9 inches in increments of 0.1 inches.
If the calculated reproduction ratio falls below the minimum reproduction ratio, the calculated reproduction ratio will be adjusted to the minimum ratio. If the reproduction ratio is over the maximum reproduction ratio, it will be adjusted to the maximum ratio. If this happens, with some ratios, parts of the image might not be copied or margins will appear on copies.
Create Margin
Reduces the image to 93% of its original size and places the reduced image at the center. By combining it with the Reduce / Enlarge functions, you can further increase a margin.
Press [Create Margin].
Select the reproduction ratio, if necessary.
You can change Ratio for Create Margin under [Reduce / Enlarge] in Settings. For details, see the following section: