Attaching the Paper Feed Unit

WARNING

It is dangerous to handle the plug with wet hands. Doing this may result in receiving an electric shock.

CAUTION

The machine weighs approximately 81 kg (178.6 lb.).

Four or more people are required to move the machine. Use the inset grips on both sides, and lift it slowly. Lifting it carelessly or dropping it may cause an injury.

Before installing options, the machine should be turned off and unplugged for at least thirty minutes. Components inside the machine become very hot, and can cause a burn injury if touched.

Before moving the machine, unplug the power cord from the outlet. If the cord is unplugged abruptly, it could become damaged. Damaged plugs or cords can cause an electrical or fire hazard.

The lower paper trays and the tray 3 (LCT) weigh approximately 22 kg (49 lb.).

To lift the machine, have two or more people hold it at the bottom on both sides, and be sure they lift it slowly and are careful not to put a strain on their bodies. Lifting it carelessly or dropping it may cause an injury.

The lower paper trays, the tray 3 (LCT), mailbox and other products are equipped with anti-tip components. Watch your step to avoid tripping. Otherwise, an injury might occur.

This section explains the installation procedure common to the following paper feed units. Check the items contained in the package of each paper feed unit.

Paper Feed Unit PB3360 (Lower paper tray)

Paper Feed Unit PB3350 (Lower paper trays)

LCIT PB3370 (Tray 3 (LCT))

llustration of Paper Feed Unit PB3360

llustration of Paper Feed Unit PB3350

llustration of Paper Feed Unit PB3370

Each package contains the followings:

Bracket (2)	Screw (3)

Only the parts specified above are used to attach the paper feed unit. The other parts included in the package are not used.

Important

When attaching multiple options, attach the paper feed unit first.
When the lower paper trays or the tray 3 (LCT) is attached, you can also attach LCIT RT3050. To attach LCIT RT3050, contact your sales or service representative.
Before using the new paper feed unit, you must configure settings in the printer driver.
Some illustrations in this section might be slightly different from the machine.
Check the machine nameplate to confirm the model code.

The procedure is the same for both units. The lower paper trays is used as an example.

Turn the machine off and unplug the power cord.
Remove the packaging from the paper feed unit.
When using the lower paper tray with the lower paper trays, two units are combined first. For details, see Attaching the Lower Paper Tray to the Lower Paper Trays.
When using the tray 3 (LCT), remove the adhesive tape on the right tray. Pull out the tray 3 (LCT) carefully until it stops.
Push the right tray carefully to the end and remove the adhesive tape.
Lift the machine using the handles on both sides.

The machine should always be lifted by at least four people.
Align the front of the machine with the front of the paper feed unit, and slowly lower it.
Place it so that it is held firmly in place by the vertical pins.
Pull out tray 2 of the machine slowly until it stops, lift the front of the tray slightly, and then pull out the tray completely.

Place the tray on a flat surface.
Attach a screw in the hole on the left side of the tray opening to secure the machine to the paper feed unit.
Tighten the screw firmly using a coin.
Lift the front of the tray, and slide it carefully into the machine until it stops.
On the rear of the unit, attach two brackets using the remaining screws.
Tighten the screws firmly using a coin.
Plug in the power cord, and then turn on the machine.
Print the configuration page to confirm that the unit was attached correctly.

Note

To confirm whether the optional paper feed unit was correctly attached, print the configuration page, and check “Attached Equipment” on the configuration page. If the unit was attached correctly, the following will be displayed:
- Lower paper tray:
  “Lower Paper Tray”
- Lower paper trays:
  “Lower Paper Trays”
- Tray 3 (LCT):
  “Tray 3 (LCT)”
If the optional paper feed unit was not installed properly, repeat the procedure from the beginning. If it cannot be installed correctly even after reattempting installation, contact your sales or service representative.

For more information about printing the configuration page, see Printing the Configuration Page.

Attaching the Lower Paper Tray to the Lower Paper Trays

CAUTION

The lower paper tray weighs approximately 12 kg (26.5 lb.).

When moving the paper feed unit, lift the optional paper feed unit slowly. Lifting it carelessly or dropping it may cause an injury.

Remove the protective cover of the paper feed unit.
Hold the lower paper tray as shown in the illustration below, and then lift it.
Align it with the top of the lower paper trays, and slowly lower it straight down.
Place it so that it is held firmly in place by the vertical pins.
Pull the tray of the lower paper tray out slowly until it stops, then lift the front of the tray slightly, and pull it out completely.

Place the tray on a flat surface.
Attach a screw in the hole on the left side of the tray opening to secure it to the paper feed unit.
Tighten the screw firmly using a coin.
Lift the front of the tray, and slide it carefully into the machine until it stops.
On the rear of the unit, attach two brackets using the remaining screws.
Tighten the screws firmly using a coin.

Proceed to the machine connection procedure. See steps from 2 on Attaching the Paper Feed Unit.

Section Top