Network/Interface
This section describes the settings in [Network/Interface] under [System Settings].
Introduction of Two Types of Setting Screens (Standard/Classic)
Machine: LAN Type
Items | Description |
---|---|
Machine: LAN Type | LAN type is displayed when wireless LAN board is installed. You can specify which you use for connection, wired LAN (Ethernet) or wireless LAN.
|
Wireless LAN
Items | Description | |
---|---|---|
Communication Mode | Specify the communication mode of the wireless LAN. The following modes are available: [802.11 Ad-hoc Mode] [Infrastructure Mode] [Direct Connection: Group Owner Mode] [Direct Connection Mode]
| |
Infrastructure Mode | SSID Setting | Specify SSID when [Communication Mode] is [Infrastructure Mode] or [802.11 Ad-hoc Mode]. In [Infrastructure Mode] enter the SSID of the connected access point. In [802.11 Ad-hoc Mode], the entered SSID will be the name of the Ad-hoc network. The characters that can be used are ASCII 0x20-0x7e (32 bytes), and are distinguished between upper and lower cases. For connecting to the access point to which ANY connection is permitted, enter blank or "ANY" in the SSID field. |
Security Method | Specify the encryption of the Wireless LAN. To encrypt, select one of WEP, WPA2-PSK, or WPA2 as the Security Method. If you select WPA2, install the authentication methods and certificate. For details about "Configuring IPsec Settings", see "Security Reference" on our website.
| |
Wireless LAN Signal | Display the machine's radio wave status when the machine is connected by specifying [Communication Mode] to [Infrastructure Mode]. If the radio wave is weak, change the access point to connect or review the machine's environment. | |
Direct Connection Mode | Wireless LAN: Direct Connection | Specify whether to enable Direct Connection: Group Owner Mode set to Active from the direct connection widget placed on the Home screen.
|
Fix SSID | Specify whether to fix SSID when the direct connection is set to Active.
| |
Direct Connection Settings | Specify to connect to the machine from the mobile device. Specify the device name, password, and machine's IPv4 address for direct connection. | |
802.11 Ad-hoc Mode | Ad-hoc Channel | Specify the channel to use when [Communication Mode] is [802.11 Ad-hoc Mode]. Select the channel depending on the radio wave status.
|
Wireless LAN: Easy Setup/Direct Connection | Specify Wireless LAN: Easy Setup/Direct Connection to connect to a WPS-compatible access point. Push the button of the access point or enter the PIN code displayed on the machine in the access point on the computer for the connection.
| |
Restore Factory Defaults for Wireless LAN Settings | You can return the wireless LAN settings to their defaults. |
IP Address (IPv4)
Items | Description |
---|---|
IP Address | Specify the machine's IPv4 Address and Subnet Mask. Machine's IPv4 Address can be specified by an address or acquired from the DHCP server automatically.
|
IPv4 Gateway Address | Specify the IPv4 address of the router or host computer used as a gateway.
|
IP Address (IPv6)
Items | Description |
---|---|
IP Address | Displays the machine's IPv6 address.
|
IPv6 Gateway Address | Displays the machine's IPv6 gateway address. |
IPv6 Stateless Address Autoconfiguration | Specify whether to specify the address automatically using IPv6 Stateless Address Autoconfiguration.
|
DHCPv6 Configuration | Specify the DHCPv6 Mode or address of the DNS server.
|
We recommend only enabling one of the following settings: [IPv6 Gateway Address], [IPv6 Stateless Address Autoconfiguration], or [DHCPv6 Configuration]. If you enable all of them at the same time, IPv6 Gateway Address is automatically changed.
An IPv6 gateway address automatically acquired may be set by the router or in accordance with the DHCPv6 server settings if one of the following settings is enabled:
Activate [IPv6 Gateway Address] and either [IPv6 Stateless Address Autoconfiguration] or [DHCPv6 Configuration].
Activate [IPv6 Stateless Address Autoconfiguration] and [DHCPv6 Configuration] at the same time.
DNS Configuration
Items | Description |
---|---|
DNS Configuration | Specify the IPv4 address of the DNS server. IPv4 Address of the DNS server can be specified by an address or acquired from the DHCP server automatically. You can confirm the connection to the DNS server.
|
DDNS Configuration
Items | Description |
---|---|
DDNS Configuration | Specify whether you use the Dynamic DNS function.
|
WINS Configuration
Items | Description |
---|---|
WINS Configuration | Specify whether to use WINS server. When the machine's IPv4 address is specified optionally, specify the primary and secondary WIN server addresses and scope ID. Do not specify "255.255.255.255" as the address of the WINS server.
|
Machine Name
Items | Description |
---|---|
Machine Name | Enter the machine name up to 31 characters. When you manage the machine with Web Image Monitor or Machine Management software, this is displayed as "Device Name". |
Host Name
Items | Description |
---|---|
Host Name | Specify the host name. When you do not specify the name, the text starting with RNP is automatically set. Enter the host name up to 63 characters. You cannot specify the host name starting with "RNP" or "rnp". You cannot enter a host name starting with or ending with a hyphen. You cannot enter a host name in which hyphens are used consecutively.
|
Domain Name Configuration
Items | Description |
---|---|
Domain Name Configuration | Specify the domain name. Obtain the domain name from the DHCP server automatically or enter the domain name up to 63 characters. |
Ethernet Speed
Items | Description |
---|---|
Ethernet Speed | Specify the access speed between the machine and the network devices. When the communication is unstable, fix the Transmission Speed to 10 Mbps or 100 Mbps. When you specify Full Duplex in this case, specify the same Transmission Speed of the connected device as the machine.
|
Effective Protocol
Items | Description |
---|---|
Effective Protocol | Select protocols to use in the network.
|
Optional Network
Items | Description |
---|---|
Optional Network | Specify the IP address, gateway address, Ethernet speed, and other settings of the device server option. |
Extended Interface
Items | Description |
---|---|
Extended Interface | The application to configure the settings for connecting to another network starts. |
SMB
Items | Description |
---|---|
SMB Computer Name | Specify the SMB computer name. When you do not specify the name, the text starting with "RNP" is automatically set. Enter the name up to 15 characters. You cannot specify a text starting with RNP. "*+,/:;<>=?[\]|. and spaces cannot be entered. |
SMB Work Group | Specify the SMB work group name. Enter the group name up to 15 characters. "*+,/:;<>=?[\]|. and spaces cannot be entered.
|
SMB Client Advanced Settings | Select the port number from 139 or 445 for the SMB data transmission. You can also specify whether to specify the SMBv2/v3 transmission Inactive. When SMBv2/v3 is Inactive, transmission is performed with SMBv1.
|
Permit SNMPv3 Communication
Items | Description |
---|---|
Permit SNMPv3 Communication | Specify the communication of SNMPv3 protocol whether to use the encrypted communication only or encrypted and cleartext communication in accordance with the settings of the machine. When you specify [Encryption Only], you need to set [Encryption Password] for the administrator by [System Settings][Settings for Administrator][Authentication/Charge][Administrator Authentication/User Authentication/App Auth.][Register/Change Administrator].
|
IEEE 802.1X Authentication
Items | Description |
---|---|
IEEE 802.1X Authentication for Ethernet | Specify when you use the IEEE 802.1X authentication for Ethernet.
For details about "Configuring IPsec Settings", see "Security Reference" on our website. |
Restore IEEE 802.1X Authentication to Defaults | Return the settings to their defaults when the machine cannot be connected with the IEEE 802.1X authentication. For details about "Configuring IPsec Settings", see "Security Reference" on our website. |
Communication Security
Items | Description |
---|---|
Permit SSL / TLS Communication | Specify the communication of SNMPv3 protocol whether to use the encrypted communication of SSL/TLS or encrypted and cleartext communication in accordance with the settings of the machine. When you specify [Ciphertext Only], you need to install the Server Certificate for the machine.
|
IPsec | Specify whether to use the machine's IP sec.
For details about "Configuring IPsec Settings", see "Security Reference" on our website. |
Control Panel: LAN Type
Items | Description |
---|---|
Control Panel: LAN Type | Specify the interface network for connecting the Mobile Device in Wi-Fi Direct mode, Wi-Fi interface on the Control Panel or Network Interface on the rear of the machine. Change the network settings on the rear of the machine by [System Settings][Network/Interface][Machine: LAN Type].
|
Control Panel: Port Forwarding
Items | Description |
---|---|
Control Panel: Port Forwarding | Specify whether to forward the Wi-Fi interface data on the control panel to the network interface on the rear of the machine. Contact your sales or service representative to use this function.
|
Control Panel: Wireless LAN Settings
Items | Description | |
---|---|---|
Wi-Fi | Specify whether to enable the Wi-Fi interface on the control panel. When set to "ON", the detected Wi-Fi network is displayed. Select the connected network and enter the password. When the Wi-Fi network you want to connect is not displayed, press [+], and then specify [Network Name], [Security], or [Password].
| |
Wireless Direct | This setting is for connecting a computer or mobile device (client) to the machine via no access point. Specify the Wi-Fi Direct operation mode and connection password.
Connecting to the Machine from a Mobile Device Using the Wi-Fi Direct Function The [Wireless Direct Settings] screen includes the following setting items: | |
Group Owner Mode | When you specify Group Owner Mode to ON, the machine functions as an access point and can be detected by multiple clients. When you specify to OFF, the machine is connected to one client.
| |
Device Name | The name of the machine displayed on the client screen. | |
Connection Password | Specify the password for connecting the client to the machine. | |
Advanced Settings | DHCP Server IP Address | Specify when [Group Owner Mode] is set to OFF. When [Wireless Direct] is set to ON, the control panel functions as a DHCP server. Specify the IP address of the control panel. |
DHCP IP Address Range | Specify the range of IP addresses assigned to the clients. The IP address assigned to the client is effective for one hour. | |
Channel | Specify the channel for connection to the client from 1 to 11.
| |
SSID Header | Specify when [Group Owner Mode] is set to OFF. Specify whether to set the header text of wireless direct network name (SSID) as "DIRECT-zV-" or not. If this setting is disabled, two characters between "-" are specified randomly.
| |
Available Devices | Specify when [Group Owner Mode] is set to OFF. The connected client name is displayed. When you press the client name, the connection is disconnected. | |
Remembered Groups | Specify when [Group Owner Mode] is set to OFF. The history of wireless direct connection is displayed. When you press the connection name, the connection is retrieved. |
Control Panel: Proxy Settings
Items | Description | |
---|---|---|
Use Proxy | Specify whether the control panel uses a proxy server for communications.
| |
Advanced Settings | Proxy Address | Enter the proxy server IP address. |
Port Number | Enter the port number for communicating to the proxy server. | |
Enable Authentication | Specify whether to use proxy authentication.
| |
Login User Name | Enter the login user name for the proxy server. | |
Login Password | Enter the login password for the proxy server. | |
Proxy Exceptions | Enter the addresses that are exceptions when you do not use the proxy server. |
Bluetooth
Items | Description |
---|---|
Bluetooth | Specify whether to activate the Bluetooth interface on the control panel.
|
Name and Discoverable Settings | You can change the machine name and discoverable settings. The name of the machine displayed on the client screen. |
External Interface Software Settings
Items | Description |
---|---|
External Interface Software Settings | Specify whether to use the Bluetooth connection to the IC card reader or mobile device for authentication. When you use the IC card reader, you can select the type (USB or NFC).
|
Ping Command
Items | Description |
---|---|
Ping Command | Confirm whether the machine can be connected to the network. Specify the IPv4 address of the device connected to the network and then press [Ping Command]. A message to indicate whether the connection succeeded is displayed on the screen. |
Print List
Items | Description |
---|---|
Print List | Prints the network settings. |
Restore Factory Defaults for Network/Interface Settings
Items | Description |
---|---|
Restore Factory Defaults for Network/Interface Settings | Initializes the network settings. |
Parallel Interface
Items | Description |
---|---|
Parallel Timing | Specify the timing for the control signal of the parallel interface.
|
Parallel Communication Speed | Specify the communication speed for the parallel interface.
|
Selection Signal Status | Specify the level for the select signal of the parallel interface.
|
Input Prime | Specify whether to validate or invalidate the input prime signal upon reception.
|
Bidirectional Communication | Specify the machine's response mode to a status acquisition request from the computer.
|
Signal Control | Specify how to handle errors that occur during printing operation. Normally it is not necessary to change. When you specify [Printer Priority], the error is sent to the computer as it is.
|
USB Port
Items | Description |
---|---|
USB Port | Specify whether to use the USB port. (mainly Europe)
(mainly North America)
(mainly Asia)
|
USB Speed
Items | Description |
---|---|
USB Speed | Specify the USB speed. You can select from [Auto Select] or [Full Speed].
|
DIPRINT Timeout Period
Items | Description |
---|---|
DIPRINT Timeout Period | Specify the timeout time for DIPRINT printing.
|
Unconnected Network Instruction Screen
Items | Description |
---|---|
Unconnected Network Instruction Screen | Specify whether to display the instruction screen when the machine is not connected to the network.
|