When Paper or an Original Is Jammed

Remove the jammed sheet by following the procedure described in the animated illustration displayed on the control panel. If paper jams occur frequently, check the condition of the paper and the settings in [Tray/Paper Settings].

Be careful not to rip the jammed paper and leave small pieces inside the machine when removing. Hold on the left and right edges of the paper firmly and apply force evenly to pull out the paper.

There are highly-heated parts inside the machine. When removing misfed paper, do not touch areas other than those specified in this manual. Touching those areas can result in burns.

When replacing paper or removing jammed paper, make sure not to trap or injure your fingers.

Do not turn off the power of the machine when removing the jammed paper. If you turn off the power, the specified settings values are reset.
Only perform the operation described in the animated illustration. Failure to do so may degrade the print quality or cause a malfunction.
Before opening the rear cover, remove the paper loaded in the bypass tray.
The area inside the rear cover contains hot surfaces. When opening the rear cover to remove paper, wait a while to allow the hot parts to cool down before performing the procedure.

Check the part where the paper jam occurred on the screen.

When the display is turned off, press [Check] in [Check Status] "Mach. Status".

Follow the procedure described in the animated illustration to remove the jammed paper.

Close all covers that have been opened.

If the jammed paper was torn apart while removing it, check that all pieces are accounted for.
If paper becomes trapped between the tray and the machine while removing jammed paper, pull out the tray completely and then remove the paper.
If you notice a paper jam about to occur in the ADF, press [Stop] to pause scanning, and place the original in the ADF again.
If the message remains displayed even after you remove the jammed paper, please check the following parts of this machine.
- Recheck the paper path and make sure that you have removed all of the jammed paper.
- Close any door that is open.

If Paper Jams Occur Frequently

Check that the paper is loaded properly and the settings in [Tray/Paper Settings] are specified correctly.

Paper condition

Items to check	Solution if applicable
Are the sheets of paper in close contact with each other?	Fan the sheets thoroughly before loading them in the tray.
Are the sheets of paper curled?	Correct the curl before loading the paper in the tray. When the paper supports duplex printing, fan the paper thoroughly and turn over the paper. To prevent paper becoming curled, store the paper horizontally on a flat surface.
Is the paper flat and not folded or wrinkled?	Load new paper with no folds or wrinkles. Do not use paper that has been used for copying or printing on a copy, printer, or MFP other than the machine.
Is the paper dry and not moist?	Load paper that has been stored in a dry environment. Store paper in an environment where the humidity is below 70 %. Once the packaging material containing the paper has been opened, place the paper in a plastic bag to keep it dry.
Is the cut surface of the paper smooth and clean?	If the cut surface is uneven, set the paper in a different orientation so that the cut surface faces another direction. When the paper supports duplex printing, turn over the paper.
Is the paper too thick? Is the paper too thin?	Check the specifications for the paper that can be used on the machine, and load paper that is supported. Recommended Paper Sizes and Types

Condition of the loaded paper

Items to check	Solution if applicable
Are too many sheets of paper loaded?	Load paper below the upper limit mark (, etc.) in the tray.
Are the side fence and end fence in the paper source tray of the mainframe properly adjusted to the paper size?	Adjust the side fence or end fence so that there is no gap between the fence and loaded paper. When loading only a small amount of paper in the tray, adjust the fences so that they do not press too tight against the paper. Push the paper tray slowly in to the machine. If the tray is pushed with force, the side fence may move slightly.
Is the bypass tray used correctly?	Set the machine in a location where the bypass tray and the loaded paper do not come in contact with the wall. Adjust the paper guides on the left and right sides of the tray to match the paper size. When loading paper that is larger than A4 or 8¹/₂ × 11, pull out the extender.

Also check the basic procedure for loading paper into the machine again.
Loading Paper into the Paper Tray

Tray/Paper Settings

Items to check	Solution if applicable
Do the paper size and the setting in [Settings][Tray/Paper Settings] match?	Specify a setting that matches the loaded paper in "Paper Size". Press [Home] () after specifying the settings.

Check the paper that can be loaded in the machine again.
Recommended Paper Sizes and Types

When a paper jam occurs on the output tray, check that there are no obstacles in the Finisher tray or Mailbox Tray. (IM C530F Only)