snmp

"IPX" is shown only when an optional NetWare unit is installed.

msh> snmp

• Default access settings 1 is as follows:

  Community name:public

  IPv4 address:0.0.0.0

  IPv6 address:::

  IPX address:00000000:000000000000

  Access type:read-only

  Effective Protocol:IPv4/IPv6/IPX

• Default access settings 2 is as follows:

  Community name:admin

  IPv4 address:0.0.0.0

  IPv6 address:::

  IPX address:00000000:000000000000

  Access type:read-write

  Effective Protocol:IPv4/IPv6/IPX

• If "-p" is added, you can view settings one by one.

• To display the current community, specify its registration number.

msh> snmp ?

msh> snmp "number" name "community_name"

• You can configure ten SNMP access settings numbered 1–10.

• The machine cannot be accessed from Device Manager NX or SmartDeviceMonitor for Client if "public" is not registered in numbers 1–10. If you change the machine's community name, change the connected computer's community name accordingly.

• The community name can be entered up to 15 characters.

msh> snmp "number" clear name

msh> snmp "number" type "access_type"

Use the following command to set protocols "active" or "inactive". If you set a protocol "inactive", all access settings for that protocol are disabled.

"IPX" is shown only when an optional NetWare unit is installed.

msh> snmp {ipv4|ipv6|ipx} {on|off}

• Specify "ipv4" for IPv4, "ipv6" for IPv6, or "ipx" for IPX/SPX.

• {on} means "active" and {off} means "inactive".

• All protocols cannot be turned off concurrently.

"IPX" is shown only when an optional NetWare unit is installed.

msh> snmp "number" active {ipv4|ipv6|ipx} {on|off}

• To change the protocol of access settings, use the following command. However, if you have disabled a protocol with the above command, activating it here has no effect.

"IPX" is shown only when an optional NetWare unit is installed.

msh> snmp "number" {ipv4|ipv6|ipx} "address"

• You can configure a host address according to the protocol used.

• The network interface board accepts requests only from hosts that have IPv4, IPv6, and IPX addresses with access types of "read-only" or "read-write". Enter "0" to have the network interface board accept requests from any hosts without requiring a specific type of access.

• Enter a host address to deliver "trap" access type information.

• To specify IPv4 or IPv6, enter "ipv4" or "ipv6" followed by a space, and then the IPv4 or IPv6 address.

• To specify IPX/SPX, enter "ipx" followed by a space, the IPX address followed by a decimal, and then the MAC address of the network interface board.

msh> snmp location "character string"

msh> snmp clear location

msh> snmp contact "character string"

msh> snmp clear contact

msh> snmp v1v2 {on|off}

msh> snmp v3 {on|off}

• Specify "on" to enable, and "off" to disable.

msh> snmp trap {v1|v2|v3} {on|off}

• Specify "on" to enable, and "off" to disable.

msh> snmp remote {on|off}

• Specify "on" to enable, and "off" to disable the SNMP v1v2 setting.

msh> snmp v3trap

msh> snmp v3trap [1–5]

• If a number from 1 to 5 is entered, settings are displayed for that number only.

"IPX" is shown only when an optional NetWare unit is installed.

msh> snmp v3trap [1–5] {ipv4|ipv6|ipx} "address"

"IPX" is shown only when an optional NetWare unit is installed.

msh> snmp v3trap [1–5] active {ipv4|ipv6|ipx} {on|off}

msh> snmp v3trap [1–5] account "account_name"

• Enter an account name up to 32 alphanumeric characters.

msh> snmp v3trap [1–5] clear account

msh> snmp v3auth algo {md5|sha1}

msh> snmp v3priv algo des/aes

msh> snmp v3priv mode {auto|on}

• Set "auto" for automatic encryption configuration.

• If you select "on", plain-text communication becomes impossible - only encrypted communication is possible.